mailto: blog -at- heyrick -dot- eu

You are not reading my b.log using HTTPS. You can switch to HTTPS by clicking here.

SimpleSeq v0.12

This version introduces a breaking change with older versions of the software. There have been changes to the channel definitions as additional things were added.

I would have done more, but I spent longer than I wanted to trying to battle with a problem in the new RODLtd internet stack. It seems as in the 7.03 release (on their website) has - for some unknown reason - decided to throw errors at boot. It looks like the origin of these issues may be the SLAAC module. Because RISC OS' error handling is a bit naff, this problem trickles up until something higher up crashes and burns. This is usually either Pinboard2 or the Freeway module (which takes out ShareFS).
It was working fine for ages. No idea why the Pi2 has suddenly started acting up like this. And even weirder, the 3B+ is running without any problems.
I'm still using the ROD stack. The "fix" was to disable IPv6.
It bothers me that it's one machine and it's just suddenly started to act up. However I think I can rule out issues with other software - I took everything out of Boot:Choices.Boot.Tasks and left only enough in Boot:Choices.Boot.PreDesk to get the stack running.
And it still crashed.
If you're interested, this is the dump of state when it crashed at boot.

 

Back to the scheduled programming... The "fconvert" program has been updated to convert both older types of file (the original ancient v0.01/v0.02 files; and those from v0.03 to v0.11), however you shouldn't need to use it since SimpleSeq has been through enough public releases now that it would simply be incompetent to only be able to handle the newer file format.

Therefore, when you load an older file (created with v0.03 or later), you will see this message:

File upgraded dialogue
Your file has been upgraded.

Saving the file (^S) will make the change permanent.

 

The reason this was necessary was to support the new channel controls.

If you press ^G you can set the stereo position of the channel. This offers seven positions, from -3 being full left, to +3 being full right. The default, obviously, is 0 in the centre.

Stereo position dialogue
Setting the stereo positions.

If you have created music, then you will only be asked to set the stereo position for channels that are in use, and they will be marked by the instrument names to aid you.
If there is no music and no channels are in use, you'll be asked to set up all 16 channels (listed by channel number).

Note that it seems, at least for my keyboard, that the drum channel (#10) appears to ignore this and just sit in the middle. Maybe percussion works to different rules?

If you press ^H you can set the volume of the channel. This offers the full control, from 0 (silent) to 127 (maximum). When translating from earlier files, the volume is set to 127. However in a new file, the default is 96 (loud but not maximum). If you enter any out of range value (like 999), it'll be clipped to 127.

Channel volume dialogue
Setting the channel volume.

Other changes are that the stereo position and volume are also included in MIDI export, and the keyboard setup prior to playing will now only set up the channels that are actually used rather than configuring all sixteen.

Here's the download:

Download simpleseq_012.zip (114.92K)
For RISC OS 5 machines with MIDI

 

 

Your comments:

Please note that while I check this page every so often, I am not able to control what users write; therefore I disclaim all liability for unpleasant and/or infringing and/or defamatory material. Undesired content will be removed as soon as it is noticed. By leaving a comment, you agree not to post material that is illegal or in bad taste, and you should be aware that the time and your IP address are both recorded, should it be necessary to find out who you are. Oh, and don't bother trying to inline HTML. I'm not that stupid! ☺ ADDING COMMENTS DOES NOT WORK IF READING TRANSLATED VERSIONS.
 
You can now follow comment additions with the comment RSS feed. This is distinct from the b.log RSS feed, so you can subscribe to one or both as you wish.

jgh, 17th October 2023, 05:20
OOoo, with a breaking change I think I'd have bumped the version straight up to v0.20.
Rick, 17th October 2023, 13:29
It's only a breaking change with respect to using newer files on *older* versions of the software. 
You can use older files on newer software, which is why the version wasn't bumped. Also, note that the *file* version ID also remains at '1' as it is broadly the same format (all "fconvert" does is copy data adding in some extra words where necessary for the extensions to the file). 
 
I don't consider this a major issue as newer (capable) versions are always available, so it's more a technicality. You shouldn't be using new files with older software. 
 
The initial releases did have an annoying message that popped up at the beginning to warn of this possibility, but I removed that as it was annoying ;) and the software became "essentially feature complete" a few releases back. What I'm doing now is enhancing it beyond that original plan. 
 
Guess what, I'm working on another release right now. ;) Just taking a break while my chips are in the air fryer...

Add a comment (v0.11) [help?] . . . try the comment feed!
Your name
Your email (optional)
Validation Are you real? Please type 76068 backwards.
Your comment
French flagSpanish flagJapanese flag
Calendar
«   October 2023   »
MonTueWedThuFriSatSun
      
24567
9101113
18
23252627
3031     

(Felicity? Marte? Find out!)

Last 5 entries

List all b.log entries

Return to the site index

Geekery

Search

Search Rick's b.log!

PS: Don't try to be clever.
It's a simple substring match.

Etc...

Last read at 14:40 on 2024/04/24.

QR code


Valid HTML 4.01 Transitional
Valid CSS
Valid RSS 2.0

 

© 2023 Rick Murray
This web page is licenced for your personal, private, non-commercial use only. No automated processing by advertising systems is permitted.
RIPA notice: No consent is given for interception of page transmission.

 

Have you noticed the watermarks on pictures?
Next entry - 2023/10/16
Return to top of page