mailto: blog -at- heyrick -dot- eu

Pi box

I bought a box for my Pi 3B+ from Amazon. Ordered it on Christmas Day, it was sent yesterday (Sunday!), and it arrived around 2pm. Uh, whoo.

It's a solid plastic box with transparent acrylic top and bottom. It comes with heatsinks for the major ICs. I added the copper heatsink to the memory on the underside, and the little heatsink to the USB and network device. I didn't need the CPU heatsink, one was already fitted.
CPUclock tells me the processor is running at 39°C, with the ambient inside being 22°C. I'm not sure I entirely trust that, as it's about 14°C in my room right now.

I also transferred across the RTC and OLED panel from the Pi2, it was a simple matter of plugging it in and dropping the driver back into !Boot.Choices.Boot.Tasks so that it runs at startup.
I did, however, have to mount the fan back to front because the people who design these cases never think to leave space for things that may be plugged into the GPIO to rest directly attached rather than using some sort of cable.

Pi 3B+ in it's new home
Pi 3B+ in it's new home.

The fan is quiet. I'm only running it on 3.3V, so it isn't going as fast as it could. On the other hand, it doesn't really seem to be moving any air. Maybe I will need to hook it up to run backwards? Questions I'll consider when it's warm enough to be a potential problem. Not that it'll be a real problem, mind you, as I have set my throttling to kick in at 55°C.

 

Speaker fail

My NetRadio is plugged into powered speakers in order to amplify the sound. They aren't anything speaker, just little ones with maybe 5cm speakers that are intended to sit either side of a monitor.
Normally they run on 4 C cells, but since I often forget to prod the power button, the batteries don't last so long.

So I decided to try using a USB splitter to tap off a second socket for power, and then get a USB to barrel plug cable to try running the speakers. They're supposed to run off of 6V (1.5V × 4), but I would imagine there's enough leeway that 5V ought to work too. Typically these sorts of amplifier chips can run on "whatever" from about 4V to 9V, the main difference being how much it can move the speaker cone.

So it was all set up. A splitter allowed one USB socket to power both the speakers (which seemed quite happy with the 5V) and the NetRadio. The NetRadio powered up, connected to the Vonets AP, and...

...oh my god, what a horrible noise!

I could quite literally hear everything that was happening on the WiFi. I can only imagine that the ESP32 was spewing noise all over the place (the LCD backlight gently flickers along with WiFi bursts) which in this arrangement was badly affecting the speakers.

Running the speakers from a different power source made the problem go away, thankfully, so all is not lost. It does, though, point yet again to the batshit crazy power consumption of the ESP32. Either that, or the cheap-ass 5V to 3.3V convertor on the board. Either way, one clearly needs to take care in how these things are actually hooked up, in order to minimise unwanted noise.

 

 

Your comments:

Please note that while I check this page every so often, I am not able to control what users write; therefore I disclaim all liability for unpleasant and/or infringing and/or defamatory material. Undesired content will be removed as soon as it is noticed. By leaving a comment, you agree not to post material that is illegal or in bad taste, and you should be aware that the time and your IP address are both recorded, should it be necessary to find out who you are. Oh, and don't bother trying to inline HTML. I'm not that stupid! ☺ ADDING COMMENTS DOES NOT WORK IF READING TRANSLATED VERSIONS.
 
You can now follow comment additions with the comment RSS feed. This is distinct from the b.log RSS feed, so you can subscribe to one or both as you wish.

Rick, 28th December 2021, 10:35
I should add that, since I had the Pi shut down, I popped the µSD into the PC and took an image of the entire thing. 
Never miss an opportunity to make another backup! 
J.G.Harston, 2nd January 2022, 03:54
Agreed. I'm doing my usual end-of-year backup of the ole MDFS into my PC. (I'll then dump the entirety of the PC onto a spare HDD and stick it in the cupboard.) 
Of course, as soon as I've done the backup it's out of date as I've been coding on one of the other machines on the network. ;)

Add a comment (v0.11) [help?] . . . try the comment feed!
Your name
Your email (optional)
Validation Are you real? Please type 18085 backwards.
Your comment
French flagSpanish flagJapanese flag
Calendar
«   December 2021   »
MonTueWedThuFriSatSun
  
17
  

Advent Calendar 2023
(YouTube playlist)

(Felicity? Marte? Find out!)

Last 5 entries

List all b.log entries

Return to the site index

Geekery

Search

Search Rick's b.log!

PS: Don't try to be clever.
It's a simple substring match.

Etc...

Last read at 12:57 on 2024/03/29.

QR code


Valid HTML 4.01 Transitional
Valid CSS
Valid RSS 2.0

 

© 2021 Rick Murray
This web page is licenced for your personal, private, non-commercial use only. No automated processing by advertising systems is permitted.
RIPA notice: No consent is given for interception of page transmission.

 

Have you noticed the watermarks on pictures?
Next entry - 2021/12/28
Return to top of page