mailto: blog -at- heyrick -dot- eu

Fixing stuff

I came home for quarter past five, and for some reason decided that today would be a good day to fix two things that bugged me.

The first thing was the weather station's rain sensor. This meant climbing up onto the woodshed, and nearly having a heart attack on seeing what it looks like on the other side. I knew there were brambles. I wasn't quite expecting this:

Oh my effing god - brambles...
To put this into context, the thing at the centre top that looks like an old waffle is the roof of an outbuilding!
This catastrophe may or may not be my summer holiday project. It depends on how much I feel like pulling the duvet over my head and hiding...

Anyway, the rain sensor was a little reed switch activated by a magnet, but dampness or something got inside, so it no longer made a clean connection when activated.
I boughy myself a pack of twenty from Amazon. Coming from Taiwan (last year, pre-COVID), it took a fair old while. However when I opened the bag, there were rather more than twenty. More like twice that. I guess somebody just threw a handful into a bag, put that into one of those dumb plastic envelopes, and stuck on the address label. Probably a lot quicker than bothering to count out twenty. ☺

How it works is that the magnet is fitted between two 'buckets' on a see-saw. Rain water drips down from a funnel above, and is directed to the upper bucket. When the bucket is heavy enough, it drops to the down position, dumping out the collected water. More rainwater will be directed this time to the other bucket, which is now the upper one.
This process repeats for as long as it is raining, and every time the buckets change position, the magnet passes the reed switch, this is noticed by the external sensor unit, and is transmitted back to the weather station.
Each tilt of the buckets registers, if I remember correctly, 0.51mm of rain. If you're wondering why it's such a weird amount (0.51 rather than, say, 0.5), it might help if I point out that it's 0.02 inches. It might be that the thing was designed for imperial measuring, and then used/sold in a metric country...

The rain sensor - inside.
I have fitted the reed switch back to front so it can sit on the side of the little circuit board that's furthest away from the magnet. That's because these reed switches are pretty sensitive.

Anyway, got everything all hooked up and went back up onto the wood shed roof to put the thing back in place.

The rain sensor - in place on the roof.
I poured water into it, and it clicked a few times as the buckets changed position. Six or seven times.
My weather report is telling me that there's be 3.62mm of rain. Well, that would be consistent with seven changes. And that would appear to be more like 0.517 mm per bucket, which equals 0.0204 inches. <shrug>

 

The next thing to look at is some of the solar powered PIR lights. Last year I installed five. A couple of weeks ago I replaced one that wasn't working with another, which wasn't working.
Of the five I had, currently only one is working.

I'm going to have to leave the two down by where Nou used to live as I need the second section for the ladder to get up on that roof to access them.
That leaves the one in the barn, and it's "new" replacement.

They were both the same basic idea. A 6V solar panel connected to a 10 LED floodlight with a little PIR sensor so it turns on upon detecting motion.
There was a "decent" quality one (solar panel plugged into the main unit) and a lower quality one (everything hardwired). The decent one is the one that failed. The lower quality one is the one that never worked.

Upon opening up the solar panel to the decent one, the problem became clear. Rain had made its way inside, and lacking a way out, had stayed there, eventually corroding the connection between the solar panel and the wire. Try as I might, I couldn't solder the wire onto the panel. How does that even work? It doesn't seem to be metal and the majority of it doesn't respond to being prodded with a multimeter.
Well, this solar panel is clearly scrap if it's not possible to attach a wire.

This leads me to consider the lower quality device. I opened up the solar panel (start with the power input). It was working as expected. So then I opened up the main part and saw three rechargable AA (LR6) cells. Two of them measured ~1.3V. One was a dud.
I decided to swap these batteries for the ones in the decent unit. I figured the batteries in there would be a better quality. I was right.
Just so I don't suffer the same problem again, I made a note of where "top" is, it being mounted probably sideways but in order to have the electrical connections to the solar panel side to side, not top and bottom. And to ensure the problem doesn't happen again like before, I used a finger drill to make three small holes to allow water to drain if it gets in.

Solar panels.
You can see the tidemark where the water collected in the plastic casing on the left. The panel in the middle (face down) was discarded. And the panel on the right (in its casing) now has drainage holes. I'm using the old school multimeter because it beeps when in resistance test. My newer meter doesn't beep, so can't be "used blind".

I've fitted the now-working replacement floodlight back into the barn. I'll need to wait until I'm out when it's dark (so, that'll be what, August?) to see if it needs any positional adjustment.

 

As for the other one, the former decent one? Well, what comes to mind is that it runs on 3 AA cells. That's nominally 1.5V × 3. Well, it's a trio of NiCads so more like 1.2V × 3. Anyway, that's 3.6V (NiCad) or 4.5V (alcaline), and the solar panel outputs about 6V in bright sunshine.
Which makes me wonder if I couldn't swap out the batteries for a USB lead, sucking off the ~5V. The unit will think it is "always on" because there'll be no solar panel (when the panel is outputting current, it's "day" and the unit is inactive). But if powered by a USB power pack, this won't be a big deal.

But, that's a project for another day. Time to go make dinner...

 

 

Your comments:

Please note that while I check this page every so often, I am not able to control what users write; therefore I disclaim all liability for unpleasant and/or infringing and/or defamatory material. Undesired content will be removed as soon as it is noticed. By leaving a comment, you agree not to post material that is illegal or in bad taste, and you should be aware that the time and your IP address are both recorded, should it be necessary to find out who you are. Oh, and don't bother trying to inline HTML. I'm not that stupid! ☺ ADDING COMMENTS DOES NOT WORK IF READING TRANSLATED VERSIONS.
 
You can now follow comment additions with the comment RSS feed. This is distinct from the b.log RSS feed, so you can subscribe to one or both as you wish.

No comments yet...

Add a comment (v0.11) [help?] . . . try the comment feed!
Your name
Your email (optional)
Validation Are you real? Please type 21817 backwards.
Your comment
French flagSpanish flagJapanese flag
Calendar
«   June 2020   »
MonTueWedThuFriSatSun
2456
81011
181920
24252628
30     

Advent Calendar 2023
(YouTube playlist)

(Felicity? Marte? Find out!)

Last 5 entries

List all b.log entries

Return to the site index

Geekery

Search

Search Rick's b.log!

PS: Don't try to be clever.
It's a simple substring match.

Etc...

Last read at 15:05 on 2024/03/19.

QR code


Valid HTML 4.01 Transitional
Valid CSS
Valid RSS 2.0

 

© 2020 Rick Murray
This web page is licenced for your personal, private, non-commercial use only. No automated processing by advertising systems is permitted.
RIPA notice: No consent is given for interception of page transmission.

 

Have you noticed the watermarks on pictures?
Next entry - 2020/07/03
Return to top of page